Aurex (Toshiba) SA-5000 Stereo Receiver — 50 WPC, Made in Japan
$395.00
1 in stock
Aurex SA-5000 by Toshiba — Fifty Silver-Face Watts a Side, Servo-Locked Tuning, Made in Japan in 1980
A 1980 silver-face receiver of genuine substance — fifty watts a side, twenty pounds on the bench, made in Japan, and wearing real wood side panels in the style of the era’s best.
Aurex, Toshiba’s Audio Marque
Aurex was Toshiba’s audio marque, and this receiver carries both names: Aurex on the faceplate, Toshiba Corporation on the rear panel. That matters mostly because it explains why a name few people recognise turns up with engineering few people expect. Toshiba was building its own semiconductors at the time, and the SA-5000 shows it — distortion is rated at three hundredths of one percent, which was serious-league territory in 1980 and would still be respectable in a modern amplifier.
Servo-Locked Tuning
The full name across the front is Servo Locked, and it is not decoration. A DC servo circuit continuously watches the amplifier’s output and corrects any drift toward direct current, which is what lets the signal path run direct-coupled, with no output capacitor sitting between the amplifier and your speakers. Take that capacitor out and the bass arrives without the softening and phase smear it introduces. It is a design choice you normally found further up the price list, and it is the reason this receiver sounds tighter at the bottom than its badge would lead you to expect.
The Control Set
The control set is complete rather than fashionable. Bass and treble with a tone defeat that lifts the entire tone stage out of circuit when you would rather it were not there. Loudness for low-level listening, a sixteen-hertz subsonic filter for warped records, a mono and stereo mode switch, and a fader. Tuning is helped along by a five-segment signal-level display and an FM muting and lock control that holds a station once you have found it. Two tape loops with full monitoring and dubbing from one to the other, phono and auxiliary inputs, and speaker switching for A, B, or both pairs together.
The Back Panel and Speaker Terminals
The back panel is equally complete: separate 300-ohm and 75-ohm FM antenna inputs alongside the AM terminals, and two AC convenience outlets rated a hundred watts each, one switched with the receiver and one always live. The speaker terminals are spring clips rather than binding posts, which means bare wire or pins — our own gold-plated flexible pin connectors are built for exactly these and make a cleaner, safer job of it than wire twisted by hand.
Condition and Service
This one arrived fully serviced, the work done by an independent technician we know and trust, and it is unusually clean for its age — the front face on its own would grade Excellent. One thing holds the overall grade at Very Good, and it is worth describing precisely: a previous owner inscribed a number into the top cover at the rear left corner. It has been polished down and does not announce itself in ordinary room light, but under a direct light you can still find it. That is the whole of it.
A few relevant specifications:
A well-made Japanese receiver from a company better remembered for televisions, at a price its better-known contemporaries no longer reach.
Available for pickup in Kanata, or shipped across Canada and internationally — we have sent equipment to fifteen countries in the past year, each piece packed in-house in 275 lb test double-wall boxes. Live shipping rates for your address are calculated at checkout. Backed by Radique Audio’s Bumper-to-Bumper Warranty and our Perpetual Trade-Back Program. Available for audition by appointment in Kanata.
Aurex SA-5000 by Toshiba Specifications
- 50 watts per channel into 8 ohms, both channels driven
- Total harmonic distortion 0.03%
- Speaker impedance 4 to 16 ohms on A or B, 8 to 16 ohms running both
- AM and FM reception; 300-ohm and 75-ohm FM antenna inputs
- Phono and auxiliary inputs; two tape loops with monitoring and dubbing
- Bass and treble with tone defeat; loudness; 16 Hz subsonic filter; fader; mono and stereo modes
- Five-segment signal-level display; FM muting and lock
- Speaker switching for A, B, or A and B together; spring-clip terminals taking bare wire or pin connectors
- Switched and unswitched AC outlets, 100 watts each
- Real wood side panels
- Introduced in 1980
- Dimensions: (Width x Height x Depth) 17.7 x 4.6 x 14.6 inches (450 x 116 x 370 mm)
- Weight: 20.9 lbs (9.5 kg)
🔌 Speaker Cable and the Right Connector
The speaker terminals here are spring clips rather than binding posts, so banana plugs and spades will not fit — our own gold-plated pin connectors are the right answer, and they make connecting and disconnecting far easier than stripping bare wire every time. We also hand-build speaker cable here in any length you need, terminated to suit, on our Custom Speaker Cable Builder. 👉
⚠️ Important Information for International Buyers
This unit is configured for North American 110/120V power. Buyers outside North America will require a step-down transformer and appropriate plug adapter.
✅ Buy With Confidence — The Radique Promise
Backed by Radique Audio’s Bumper-to-Bumper Warranty and our Perpetual Trade-Back Program. When you’re ready to move on, we’ll take it back. That’s the Radique difference.
📦 Watch how we protect your gear — our unboxing video.
📺 Curious about our business? Check out our YouTube channel for behind-the-scenes videos and more!
📞 Questions? Use the Ask a Question button above, or call us at 613-416-9995.
| Weight | 22.9 lbs |
|---|---|
| Dimensions | 18.6 × 21.7 × 8.6 in |
You may also like…
Rectilinear XI Speakers — Lattice Grilles, Walnut, Recapped, USA
Monitor Audio Bronze 3 Towers — Shot-Loaded, Made in England
Custom Speaker Cables Banana to Pin – 25′, Radique Audio
A pair of 25-foot runs in our red and black 12 AWG house wire, hand-assembled here to order — gold-plated banana plugs on one end, flexible gold-plated pins on the other, both with dual set screws and colour-coded jackets. Every joint sleeved in matching heat shrink. Honest about the gauge: it measures closer to a boutique 14 AWG. Any combination of ends on request.
Gold Plated Pin Connectors – Flexible Pins, Radique Audio
Made for spring clips and guillotine terminals, where bare wire frays and works loose. The pin flexes rather than sitting rigid, so it does not lever on a forty-year-old terminal, and two set screws hold the wire instead of one. Takes 12 to 18 AWG — 12 is a tight fit. Colour-coded non-conductive jackets and a textured grip. Sold in 1, 2, 4 or 10 pairs.
Gold Series RCA Stereo Interconnect | Radique Audio
Radique Audio Gold Series RCA Stereo Interconnect — dual RCA to dual RCA with vintage-safe, gold-plated connectors and 6-layer shielded construction. Featuring 262 strands of tinned copper, dual-layer copper and foil shielding, and slim narrow-profile connector barrels designed to fit tightly spaced vintage RCA jacks. Available in 0.2 m, 0.75 m, and 1.5 m lengths. Audiophile quality without the audiophile pricing.
Related Products
Technics SA-600 AM/FM Stereo Receiver 70 WPC — Japan
Sherwood S-8250 CP AM/FM Stereo Receiver 25 WPC
Twenty-five watts a channel into 8 ohms from Sherwood's Certified Performance series — the range where Sherwood printed the measured figures for the individual unit rather than for the model. MM phono, noise filter, mute/mono, loudness and A/B speakers, behind a brushed aluminium face with walnut-grain side panels. Level 2 serviced here: bias and DC offset set, every control deoxidised.
JVC JR-S201 Receiver – 35 WPC, Japan, SEA EQ, Excellent
Thirty-five watts a channel at 0.01% distortion with a damping factor of 70 — numbers most larger receivers of 1978 could not reach. A five-band S.E.A. graphic equalizer sits on the front panel at 40, 250, 1k, 5k and 15kHz, alongside MM phono, two tape loops and push-button speaker terminals. Made in Japan, arrived professionally serviced; cosmetically graded Excellent.
Pioneer SX-50 Silver Face Receiver – 50 WPC, Pre-Outs, 1983
Fifty watts a channel into 8 ohms at 0.007% distortion, and — unusually for a receiver this size — pre-out and main-in jacks on the back, so it can feed a subwoofer, take an equalizer in the loop, or hand off to a larger power amp. Introduced in 1983 with switchable CD and TV audio inputs, presets held by three AA cells, and the silver face of the decade that was ending. Graded Very Good.
Kenwood KR-A4070 Stereo Receiver – 60WPC, Phono, Original Remote
Sixty watts a channel into 8 ohms across the full band at 0.01% distortion, with an MM phono input at 2.5mV, a tape monitor loop, and separate bass, treble and balance. The original Kenwood remote is here, which is uncommon on a receiver of this age. Level 1 serviced; cosmetically graded Good, with honest wear for its years.
Sherwood S-7250 CP Stereo Receiver – 20WPC, Phono, Wood Cabinet
Twenty watts a channel into 8 ohms across the full 20 Hz to 20 kHz band, an MM phono input at 80 dB signal-to-noise, and a tape monitor loop. Sherwood built these in small runs in Chicago and sold them through the same shops that carried Marantz and McIntosh. Still in its original wood cabinet. Level 1 serviced here; condition Very Good.

















