Klipsch RF-62 Reference IV Floorstanding Speakers, Pair — 97dB
$557.00
The RF-62 is the tower that made Klipsch's Reference line the default answer for anyone who wanted a big, unforced sound without buying a big, expensive amplifier to get it.
✔️ Condition: Good — cabinets carry touched-up wear; drivers Very Good throughout
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Curbside delivery, local collection or freight within Canada
1 in stock
The RF-62 is the tower that made Klipsch’s Reference line the default answer for anyone who wanted a big, unforced sound without buying a big, expensive amplifier to get it.
Start with the number that matters most on this speaker: 97 decibels at one watt. That is roughly eight times as loud, for the same power, as a typical 88dB bookshelf speaker. A ten-watt amplifier drives these to a volume most people never use. A vintage 35-watt receiver drives them past the point of politeness. It means the amplifier you already own is almost certainly enough, and it means the first watt — the one doing the work on quiet passages — is being asked to do far less, which is where the sense of ease comes from.
That efficiency comes from the horn. The tweeter is a one-inch titanium compression driver on a 90-by-60-degree square Tractrix horn, with a large ceramic motor behind it. A horn does not push air the way a dome does; it couples the driver to the room, which is why it goes loud on so little and why the treble stays composed when the volume goes up. The controlled dispersion is the other half of it — the sound is aimed into the room rather than sprayed at the side walls, so these are less fussy about room treatment and placement than most towers.
Below the horn sit two six-and-a-half-inch Cerametallic woofers with the inverted copper dust caps that give the Reference line its face. The ceramic-over-aluminum cone is very stiff for its weight and damps quickly, which is what keeps the bass from smearing into the midrange. They cross over to the horn at 1,800 hertz and run down to 38 hertz, loading through twin rear-firing ports.
The cabinet is braced internally and ribbed around the horn mouth and the lower panel — the parts of a tall, narrow box most likely to sing along with the music. At 54 pounds each these are substantially built.
Each cabinet stands just over forty inches tall and only eight and a half inches wide, in black vinyl, with a low-diffraction grille that attaches magnetically — no visible pegs or holes in the baffle when the grille is off.
Condition is Good. The drivers are Very Good throughout — horns, woofers and surrounds all sound and look as they should. The cabinets carry minor wear from use, which has been touched up, and the pair presents well.
A few relevant specifications:
A pair of efficient, horn-loaded Klipsch towers that will play louder and easier on a modest amplifier than almost anything else you can put in the room. Backed by Radique Audio’s Bumper-to-Bumper Warranty and our Perpetual Trade-Back Program. Available for audition by appointment in Kanata.
Klipsch RF-62 Reference IV Specifications
- Two-way floorstanding loudspeaker, bass reflex via twin rear-firing ports
- Sensitivity 97 dB at 2.83 V / 1 m
- Frequency response 38 Hz to 23 kHz, ±3 dB
- Power handling 125 W RMS, 500 W peak
- Nominal impedance 8 ohms compatible
- High frequency: 1″ titanium-diaphragm compression driver on a 90° x 60° square Tractrix horn
- Low frequency: dual 6.5″ Cerametallic cone woofers with inverted copper dust caps
- Crossover point 1,800 Hz
- Internal cross-bracing; baffle ribbing at the lower panel and horn mouth
- Black vinyl finish
- Magnetically attached low-diffraction grilles
- 54 lbs (24.5 kg) each
- Dimensions: (Width x Height x Depth) 8.5 x 40.6 x 15.5 inches (21.6 x 103.1 x 39.4 cm), height with feet
- Weight: 54 lbs (24.5 kg) each
🔌 Speaker Cable, Bi-Wiring and Connectors
The dual posts here take bare wire, spades, pins or bananas, and they mean you can bi-wire or bi-amp if you ever want to. Our bi-wire speaker bridges replace the factory straps with something considerably better made. We hand-build speaker cable here in any length you need on our Custom Speaker Cable Builder, terminated with our own gold-plated banana plugs or spade connectors. 👉
🚚 Curbside Delivery — This Item Ships Differently
These weigh 54 lb each, which is over the limit we courier a speaker of this size at. Instead we offer personal curbside delivery by our own vehicle, collection in person from us in Kanata, or freight anywhere in Canada. Please contact us before purchasing — use the pink Ask a Question button on this page and include your postal code, and we will come back with pricing and timelines so you can decide before you buy. Full details and coverage area are on our Curbside Delivery page. 👉
✅ Buy With Confidence — The Radique Promise
Backed by Radique Audio’s Bumper-to-Bumper Warranty and our Perpetual Trade-Back Program. When you’re ready to move on, we’ll take it back. That’s the Radique difference.
📦 Watch how we protect your gear — our unboxing video.
📺 Curious about our business? Check out our YouTube channel for behind-the-scenes videos and more!
📞 Questions? Use the Ask a Question button above, or call us at 613-416-9995.
| Impedance | 8 Ω |
|---|---|
| Power Handling | 101–200 W |
| Sensitivity | 96 dB + |
| Woofer Size | 6–7″ |
Klipsch began in Hope, Arkansas, in 1946, when Paul W. Klipsch started building his corner-horn Klipschorn, and its Heritage speakers are still built by hand in Hope. We carry Klipsch towers, centre channels, bookshelf speakers and subwoofers. We've had more than 160 Klipsch listings so far. Every used Klipsch here is inspected, tested and serviced as required, then photographed in-house and covered by our Bumper-to-Bumper Warranty and Perpetual Trade-Back Program. Don't see the model you want? Tell us on First Dibs and we'll email you when one arrives.
The Klipsch story, 1946 to today
Paul W. Klipsch was posted to Hope, Arkansas, in 1941 as an Army officer. He patented his corner-horn design in the mid-1940s and founded Klipsch in Hope in 1946; Klipsch says its first speaker was built by hand there that year, with the horn made in a tin shed. He hired his first employee in 1948.
The Heritage line. The Klipschorn of 1946 was followed by the Heresy (1957), designed as a centre speaker to sit between a pair of Klipschorns, the Cornwall (1959), the La Scala (1963) and the Forte (1985).
A new generation. Fred Klipsch bought the company from Paul Klipsch in 1989, and headquarters later moved to Indianapolis. Paul Klipsch died in 2002 at 98. The Reference Series arrived in 1999.
A Canadian connection. In 2006 Klipsch bought Audio Products International of Toronto, with its Energy and Mirage brands. Audiovox, later VOXX, bought Klipsch in 2011, and Gentex bought VOXX in 2025.
Which Klipsch is which?
Heritage: the Klipschorn, Heresy, Cornwall, La Scala and Forte, built to order by hand in Hope. Drivers change between generations, so identify the version.
KG series (mid-1980s to early 1990s): lower-priced horn-tweeter floorstanders such as the KG 4 (1985 to 1992) and KG 5.5.
Reference (1999 onward): horn-tweeter towers, bookshelf speakers and centres, from the RB-5 and RF-7 to the later RF, RB and RC models.
Synergy (late 1990s and 2000s): such as the KSF 8.5 and the SF-1.
Subwoofers: powered models such as the RPW-10.
Buying used Klipsch: what to check
Horn diaphragms. The compression drivers in older Klipsch speakers age; owners report tired midrange diaphragms on Heritage models and raspy tweeters on some KG pairs. Listen to each horn on its own at a moderate level.
Reference tweeters. A crackling tweeter can be a loose connection, and owners say these tweeters can fail if played very loud.
Crossovers and passive radiators. Many Heritage and KG owners recap their crossovers, and KG passive radiators can have cracked surrounds.
Modifications. Aftermarket diaphragms and crossovers are common upgrades on Heritage and KG models. Ask what has been changed.
Where it was made. Heritage models are built in Hope. Check the label before calling any other Klipsch "made in USA".
Everything we list is inspected, tested and serviced as required here, and comes with our warranty.
You may also like…
JBL Northridge E80 3-Way Towers – Cherry, Bi-Wirable, Pair
A four-driver JBL tower in the Cherry finish, with a genuine bi-amp panel.
✔️ Condition: Very Good — cabinets present well, working properly
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Expertly packed for safe shipping
Paradigm Monitor 7 v2 Towers – Light Cherry, Made in Canada
A slim three-driver tower from Paradigm's Mississauga years, in the uncommon Light Cherry finish.
✔️ Condition: Very Good — cabinets present well, working properly
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Expertly packed for safe shipping
IsoAcoustics GAIA II Speaker Isolators (Set of 4)
- ✔️ Genuine IsoAcoustics, brand new, from an authorized Canadian dealer
- ✔️ A set of 4 isolators for one floor-standing speaker or subwoofer up to 120 lb (54 kg)
- ✔️ Screws in place of your spikes: M6-1.0, M8-1.25 and 1/4″-20 adaptors included
- ✔️ Machined stainless steel, dark chrome, 2 × 1.7 in (51 × 43 mm) per isolator
- ✔️ Pick up in Kanata by appointment, or shipped across Canada and internationally
Harman Kardon HK3700 Stereo Receiver – 85 WPC, Sub Out
A Harman Kardon HK3700 network stereo receiver, thoroughly tested and working perfectly, with a Harman Kardon remote.
✔️ 85 watts per channel into 8 ohms
✔️ Moving magnet phono stage and a subwoofer pre-out
✔️ Ethernet for DLNA and vTuner internet radio, USB for iOS devices
✔️ Thoroughly tested, with HK remote and a PDF manual
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Expertly packed for safe shipping
IsoAcoustics GAIA III Speaker Isolators (Set of 4)
- ✔️ Genuine IsoAcoustics, brand new, from an authorized Canadian dealer
- ✔️ A set of 4 isolators for one floor-standing speaker or subwoofer up to 70 lb (32 kg)
- ✔️ Screws in place of your spikes: M6-1.0, M8-1.25 and 1/4″-20 adaptors included
- ✔️ Stainless steel, 1.7 × 1.5 in (43 × 39 mm) per isolator
- ✔️ Pick up in Kanata by appointment, or shipped across Canada and internationally
Custom Speaker Cable Builder
Your specs, your cable: choose the cable, the length and each connector, with live pricing.
- House CCA, House OFC, House Quad, Kimber 4PR or Kimber 4TC
- Banana, spade, pin, small spade or bare wire, chosen for each end
- Bi-wire on Kimber 4PR, Kimber 4TC and House Quad
- Hand-assembled, heat-shrink reinforced and colour-coordinated
- 1-year warranty
Related Products
Acoustic Research TSW 510 Vintage Towers, Pair – Refoamed, Oak
A pair of Acoustic Research TSW 510 three-way floorstanding speakers from the late 1980s, with solid oak tops and plinths, freshly refoamed.
✔️ Freshly refoamed woofers and midranges
✔️ Very good condition, grilles included
✔️ 3-way acoustic suspension, 10" woofer, titanium tweeter
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Curbside delivery, local collection or freight within Canada
Paradigm 11se Mk II Towers, Pair — Dual 8″, Made in Canada
Built in Canada by Paradigm, and the largest speaker in the SE range — the one the rest of the series was working up to.
✔️ Condition: Good — cabinets touched up; repaired and working correctly
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Curbside delivery, local collection or freight within Canada
Focal Chorus 714V Floorstanders, Pair — Light Walnut, France
A pair of Focal Chorus 714V floorstanding loudspeakers in Light Walnut, made in France.
✔️ Condition: Very Good — thoroughly inspected and tested
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Expertly packed for safe shipping
JBL Northridge E80 3-Way Towers – Cherry, Bi-Wirable, Pair
A four-driver JBL tower in the Cherry finish, with a genuine bi-amp panel.
✔️ Condition: Very Good — cabinets present well, working properly
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Expertly packed for safe shipping
Mirage OMNI 350 Omnipolar Towers – Designed in Canada, Black Ash
A pair of slim Mirage towers built around the company's Omnipolar design, in very good condition, that fill a room with sound instead of aiming it at one chair.
✔️ Very Good condition — black ash cabinets, drivers and grilles present cleanly
✔️ Designed and engineered in Canada around Mirage's room-filling Omnipolar sound
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Expertly packed for safe shipping
Monitor Audio Silver S8 Towers – Made in England, Warm Beech
A pair of three-way Monitor Audio towers from the Silver S range, in very good condition, with a metal driver in every position and a warm beech veneer that suits almost any room.
✔️ Very good condition — free of significant marks, in Warm Beech real wood veneer
✔️ Made in England, with Monitor Audio's C-CAM metal drivers throughout
✔️ Bi-wire and bi-amp ready — two pairs of 5-way binding posts per speaker
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Expertly packed for safe shipping
JVC Theatre Series SP-5500 Tower Speakers, Pair – 8-inch Woofers
A pair of JVC Theatre Series SP-5500 two-way tower speakers in black woodgrain, with front-ported bass-reflex cabinets, tested on our bench and in very good condition.
✔️ Very good condition — free of significant marks, grilles included
✔️ 8-inch woofers in front-ported Theatre Series towers
✔️ Built-in circuit breaker protects the tweeters
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Expertly packed for safe shipping
Vintage Pioneer CS-77 12″ 3-Way Speakers, Pair – Made in Japan
A pair of late-1960s Pioneer CS-77 three-way speakers, made in Japan, in walnut veneer cabinets with their wooden diamond-lattice grilles. Their High Level controls have been freshly serviced, they have been tested on our bench, and they are in good condition.
✔️ Good condition — walnut veneer, wooden lattice grilles included
✔️ High Level controls freshly serviced, tested on our bench
✔️ 12-inch woofer, three-way design — made in Japan, late 1960s
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Expertly packed for safe shipping
Linn Keilidh Floorstanding Speakers, Pair – Made in Scotland
A pair of Linn Keilidh floorstanding speakers, built in Glasgow, Scotland, in Linn's deep red Rosenut veneer, set up for bi-wiring.
✔️ Tested on our bench
✔️ Very good condition
✔️ Bi-wire ready: build your cable with our Cable Builder
✔️ Covered by Radique Warranty
✔️ Includes Perpetual Trade-Back Program eligibility
✔️ Expertly packed for safe shipping



















